You are here: Home1 > Products2 > Hazardous Location3 > CS54 Non-Incendive Differential Pressure Transducer
CSA Class I, Division 2, Groups A, B, C, D T4 Approved
Non-Incendive Differential Pressure Transducer
**Disclaimer: Unless otherwise agreed in writing, Core Sensors products are not authorized for use in applications including medical devices, life support systems, in-flight aerospace, nuclear or any other application where the product failure could result in personal injury or death.
The CS54 Non-Incendive Differential Pressure Transducer is a high strength sensor designed for differential pressure measurements of liquids and gases in Class I, Division 2 hazardous locations. A 316L SS oil filled sensor element provides excellent stability over a wide operating temperature range while offering corrosion resistance against various liquids and gases. Differential pressure ranges up to 50 PSI are available with 1/4″ MNPT or FNPT process connections.
Caution must be taken when installing and operating the CS54 in known Class I, Division 2 hazardous locations. Please review the Non-Incendive Operating Instructions prior to installation.
No Conduit Installation Required!
In an effort to simplify installation in Class I, Division 2 hazardous locations, the CS54 Non-Incendive Differential Pressure Transducer is offered with an integral Turck Minifast electrical connection.
When combined with a CSA Division 2 approved Turck cordset and a Turck Lokfast Guard, there is no requirement for conduit to be installed over the cable*. This not only makes installation easy but also makes switching out sensors less cumbersome. Core Sensors can supply all components as a complete package. Click here to learn more about the Turck Minifast electrical connection.
* Core Sensors recommends confirming hazardous location installation requirements with your local inspector as each installation is unique.
Accuracy @ 25°C*
≤ ± 0.25% BFSL
≤ ± 0.5% BFSL (2 PSI & below)
Stability (1 Year)
≤ ± 0.25% of FS
Pressure Cycles
4 million
Max Line Pressure**
500 PSI
Max Differential Pressure
50 PSI
Overpressure***
2X or 500 PSI, whichever is less, configured differential pressure
Burst Pressure***
3X configured differential pressure
* Accuracy includes non-linearity, hysteresis and non-repeatability
** Max line pressure is the highest common mode pressure that can be applied to the sensor without damage.
*** Overpressure and burst pressure are the maximum differential pressure that can be applied to the high or low side before damage to the sensor will occur.
Operating Temperature
-40 to +80°C
Operating Temperature
(Electrical connection “F”, DIN 43650-A)
-20 to +80°C
Media Temperature
-40 to +125°C
Media Temperature
(Electrical connection “F”, DIN 43650-A)
-40 to +105°C
Compensated Temperature
0 to +55°C
Storage Temperature
-40 to +125°C
TC Zero
≤ ± 1% of FS
≤ ± 2% of FS (2 PSI & below)
TC Span
≤ ± 1% of FS
≤ ± 2% of FS (2 PSI & below)
EMI/RFI Protection
Yes
IP Rating*
IP65 minimum
Vibration
10g, 20 to 5000Hz
Shock
100g, 11msec, 1/2 sine
* IP Rating is dependent on electrical termination selected. Contact factory for more information.
* IP Rating applies when electrical connector is attached with the appropriate ingress protection.
Outputs
4-20mA
Excitation
10-28VDC
Current Consumption
20mA, typical
Output Load
0-800 Ohms @ 10-28VDC
Frequency Response (min)
~250Hz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max
Outputs
1-5V
Excitation
10-28VDC
Current Consumption
<10mA
Output Load
5K Ohms, min
Frequency Response (min)
~1kHz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max
Outputs
0.5-4.5V ratiometric
Excitation
5VDC +/- 0.5V
Current Consumption
<10mA
Output Load
5K Ohms, min
Frequency Response (min)
~1kHz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max
Outputs
0.5-2.5V non-ratiometric
Excitation
3-5VDC unregulated
Current Consumption
≤ 3mA
Output Load
5K Ohms, min
Frequency Response (min)
~1kHz
Zero Offset (of FS)
≤ ± 0.5% typical, ± 1% max
Span Tolerance (of FS)
≤ ± 0.5% typical, ± 1% max
Specifications are subject to change without notice
Not all configurations are available. Our sales team can recommend the closest available configuration based on your requirements.
Contact Core Sensors for configurations not shown.
– Ordering Example: CS54-AA00010PD4H000-00 (1/4″ Female NPT, 316L SS, 0-10 PSI differential, 4-20mA, Turck® Minifast®)
Note: Mobile users can use the zoom feature to view the model number configuration matrix clearly.
Note that dimensions are for reference only. Please contact us if you do not see a dimension listed.
Note: Mobile users can use the zoom feature to view the dimensions clearly.
Have questions? Need a quote? We are ready to help! Fill out the form and a member of our sales team will contact you to discuss your requirements. You can also give us a call at (862) 245-2673.